PowerTrimm Midi L | 4,75mm (3/16") | Anodized Black

€90.00*

Content: 1 Piece

Currently not stocked

Product number: 1770-Midi-L

Shipping weight/volume: 0.1 kg

Product information "PowerTrimm Midi L | 4,75mm (3/16") | Anodized Black"

For fine adjustment

The Power Trimm Midi L from MTC has an optimal fine adjustment by the high-performance sliding bearing. Thus the inclination of the drive can be adjusted individually.

That fits

Suitable for boats up to 1100mm.

Good to know

Why slide bearings? Plain bearings convince against ball bearings due to maintenance-free operation and a long service life.
We recommend the use of 2 x M3 screws and nuts for assembly. A little trick helps when marking the holes at the stern. To do this, place a sheet of white paper on the rudder pedestal and draw over it several times with a pencil. In this way, you can “trace” the exact contours of the bracket. Now simply cut out the template, stick it to the hull with adhesive tape and drill the required holes.

Total length:	114mm (4,49")
Length to end DD:	88mm (3,46")
Width:	35mm (1,38")
Height:	37mm (1,46")
Shaft:	Outer diameter 6mm \| Suitable for 4,75mm (3/16") flex shaft
Material:	Aluminium \| Anodized black

PowerTrimm Midi L | 4,75mm (3/16") | Anodized Black

Product safety information

Manufacturer:

MTC-Modell & Technik Center
Christoph Raschke
Mozartstrasse 16
09119 Chemnitz | Germany
Email: shop@mtc-powerboat.de

That fits

Flex shaft | 4,75mm (3/16") | 100cm (39,37") | Left

Highest quality for highest demandsWith our flex shaft your project will have no limitThe advantages at a glance:High quality for high power setups4,75mm (3/16") diameterProduct photo shows delivered directionThats how its doneFor best connection we recommend to sand back the flex shaft end, degrease and glue into the prop shaft with Loctite.

€15.50*

Flex shaft | 4,75mm (3/16") | 100cm (39,37") | Right

€15.50*

Brass PTFE Hose | Steven pipe | 7mm (0,27") | 30cm (11,81") length

Protection for your flex shaftOur brass ptfe hose ensures free spinning for your flex shaft inside your boat and avoids vibration.The advantages at a glanceEasily bandable bras pipe for individual adjustment to your boatSuitable for 4,75mm (3/16") flex shaft Greasy PTFE material avoids friction between flex shaft and brass pipeThats how its doneWe recommend to grease your flex shaft frequently.

€8.00*

Flex safety | 4,75mm (3/16")

Security and thrust bearingThe advantages at a glance The ball bearing in the flex shaft lock prevents vibrations and also serves as a thrust bearing The two-piece retaining ring guarantees precise attachment Manufactured from high-strength aluminum 7075That's how it's done Slide the flex shaft lock over the brass/PTFE tube Using a screwdriver or similar, mark the hole in the brass/PTFE tube through the opening for the grease nipple Take the flex shaft lock from the brass/PTFE tube and drill the hole in the tube at the marked point You can then mount the flex shaft lock completely on the brass/PTFE tube and now conveniently grease the internal flex shaft using the grease nipple Good to knowRegular greasing of the flex shaft via the grease nipple significantly increases the durability of the material. We recommend using flex shaft grease for this.

€23.00*

Support | Steven pipe | Brass pipe | 7mm (0,28")

Securing the brass - PTFE tubeThe advantages at a glance Securely mount the brass PTFE tube in your boat Height individually adjustable The flex shaft is prevented from swinging up Manufactured from high-strength aluminum 7075How its doneFor easy assembly, we recommend using polymer glue. To do this, degrease the fuselage at the required point using brake cleaner and then glue in the stern tube holder.

€16.00*

Propeller size: 42mm (1,65")

Great product at a low priceThese CNC-machined hydropropellers, made from full aluminium, get your boat on course quicklyThe advantages at a glance Made from high quality aluminum High resistance and durability Fully roadworthy | no grinding and balancing necessary With Drive Dog

from €15.00*