Chief 60 | 1560mm (61,41") | Several versions
€540.00*
Content:
1 Piece
Preorder, Delivery time: 14 - 28 labor days**
Product number:
1760
Shipping weight/volume:
10.5 kg
Product information "Chief 60 | 1560mm (61,41") | Several versions "
Back again
The well known race boat based on the american raceboat.
The advantages at a glance
- Several assembly options such as rudder strut system | Z- drive
- Suitable for 50er in- and outrunner motors
- Suitable for 50ccm gasoline motors
Good to know
- The center of gravity is at 26-30 % starting from transom
- Made with so called sandwhich system wet in wet (1x layer 100er GFK, 1 x layer 160er GFK, 1x layer 100er GFK
Please notice that this product is not a ready to drive product.
This model is a model building accessories, therefore no toy.
If you have further questions, please contact us directly
| Length: | 1560mm (61,42") |
|---|---|
| Width: | 385mm (15,16") |
| Height: | 300mm (11,81") |
| Weight: | approx. 4900g (approx. 10,80lbs) |
| Material: | GFK/ FRP (Fibre glass reinforced plastic) |
| Color: | White |
| Center of gravity for assembly: | 26-30% from transom |
Chief 60 | 1560mm (61,42") | Several versions
Product safety information:
Manufacturer:
MHZ GmbH
Hauptstrasse 61a
96182 Reckendorf | Germany
Email: shop@mhz-powerboats.com
Hauptstrasse 61a
96182 Reckendorf | Germany
Email: shop@mhz-powerboats.com
That fits
%
Bundle Box | Rudder Strut Set | Midi | 6,35mm (1/4")
Length rudder blade:
155mm (6,10")
Universal complete system for your boat from 120cm (47,24")Bundle Box for fast and easy assembly
Thats included:1x Rudder - strut system with linkage levers on both sides | 10681x Thrust washer made of PEEK material 1x Brass PTFE pipe 10mm x 30cm | 10031x Flex shaft 6,35mm (1/4") | 10051x Hull transmission 10mm (0,39") | 1070-1.31x Steering | 1833The advantages at a glance: Two-sided rudder linkage device Height adjustable strut Waterproof, clean finish with rubber sleeve guide Black anodizing for added protection against corrosion Extra reinforced mounting flange up to the rudder boom - therefore absolutely torsion-proof The rudder blade is designed in such a way that it automatically folds up in the event of an impact with flotsam in order to prevent damage Rudder blade available in several lengthsGood to knowWe recommend using 4 x M4 screws for assembly. A little trick helps when marking the holes at the rear. To do this, place a piece of white paper on the rudder stand and stroke over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.
from €149.00*
instead of
€187.60*
single purchase price (20.58% saved)
Rudder Strut Set | Maxi | 6,35mm (1/4")
Length rudder blade:
155mm (6,10")
Universal complete system for your boat from 150cm (59,1")The advantages at a glance: Two-sided rudder linkage device Height adjustable strut Waterproof, clean finish with rubber sleeve guide Black anodizing for added protection against corrosion Extra reinforced mounting flange up to the rudder boom - therefore absolutely torsion-proof The rudder blade is designed in such a way that it automatically folds up in the event of an impact with flotsam in order to prevent damage Rudder blade available in several lengthsThats included: Rudder - strut system with linkage levers on both sides Thrust washer made of PEEK material Good to knowWe recommend using 4 x M4 screws for assembly. A little trick helps when marking the holes at the rear. To do this, place a piece of white paper on the rudder stand and stroke over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.For further questions please contact us
from €150.00*
Z-drive | S6 | 4,75mm (3/16")
Popular classic in new best formAs the successor to our sterndrive, we decided to design a new and improved version of the S6 sterndrive.
The improvements at a glance:The body of the Z-drive is no longer made of cast aluminum, but of CNC-milled aluminum 7075The surface is compacted and additionally protected against corrosion and refined by anodizingClosed lubrication with low-viscosity gear grease. Smearing in the boat as in the predecessor is therefore a thing of the pastHelical gears are not pressed, but CNC milled, hardened, ground and therefore much more accurate and robustAll drive shafts are made of stainless steel (V2A). The upper shaft has two bearings, the lower shaft has three bearings and both are sealed by a SimmerringThe output speed is 1:1 Each drive is assembled by hand directly at and by us. A drilling template is also included in the scope of delivery and makes installation easier for you. Good to knowThe drive has a square mount for 6.35mm (1/4") flex shaft. The S6 drive can be used for both left and right rotation Suitable for boats from approx. 1200mm (with double drive 1400mm length) Suitable for 50 electric motors max. 32,000 rpm and 26-32cc power Suitable for use with semi-submerged propeller The drive has a PTFE holder. The brass tube is not inserted into the drive and must be individually supported separately. We recommend a double support at the level of the coupling and the drive.The peak of the torpedo should be for hulls with steps 2-4mm below keel line for hulls without steps 2-4mm above the keel line for assembly Care instructionsThe drive must be commissioned in water only, as otherwise insufficient cooling can lead to damage to the shaft seal. The drive should be greased as required.For further questions please contact us
€369.00*
Z-drive | S6 | 6,35mm (1/4")
Popular classic in new best formAs the successor to our sterndrive, we decided to design a new and improved version of the S6 sterndrive. The improvements at a glance:The body of the Z-drive is no longer made of cast aluminum, but of CNC-milled aluminum 7075The surface is compacted and additionally protected against corrosion and refined by anodizingClosed lubrication with low-viscosity gear grease. Smearing in the boat as in the predecessor is therefore a thing of the pastHelical gears are not pressed, but CNC milled, hardened, ground and therefore much more accurate and robustAll drive shafts are made of stainless steel (V2A). The upper shaft has two bearings, the lower shaft has three bearings and both are sealed by a SimmerringThe output speed is 1:1 Each drive is assembled by hand directly at and by us. A drilling template is also included in the scope of delivery and makes installation easier for you. Good to knowThe drive has a square mount for 6.35mm (1/4") flex shaft. The S6 drive can be used for both left and right rotation Suitable for boats from approx. 1200mm (with double drive 1400mm length) Suitable for 50 electric motors max. 32,000 rpm and 26-32cc power Suitable for use with semi-submerged propeller The drive has a PTFE holder. The brass tube is not inserted into the drive and must be individually supported separately. We recommend a double support at the level of the coupling and the drive.The peak of the torpedo should be for hulls with steps 2-4mm below keel line for hulls without steps 2-4mm above the keel line for assembly
Care instructionsThe drive must be commissioned in water only, as otherwise insufficient cooling can lead to damage to the shaft seal. The drive should be greased as required.For further questions please contact us
€369.00*
%
Scorpion HK-5035-760KV | Bundle Box | 7,4KW | Water cooled | Outrunner
Bundle box for fast and easy assembly Scorpion 5035-760KV motor comes as a set including required CFK motor mount and coupling. No long search and everything fits 100%.Thats included1x Motor Scorpion 5035-760KV water cooled | 2136-W Screws Cooling water nipple 1x CFK motor mount | 2136-M1x Collet clutch 10 - 6,35mm (0,39" - 1/4") | 1023-10The advantages at a glanceOutrunner motor with high efficiencyDirect water cooling inside motor - cooling water nipples are connected to motor directly through the opposite millings for water nipplesThe third milling has to be closed with a set screwLarge ball bearings for high stability and long service life4 screws M4, 3 x cooling nipple M4 included to deliveryRotation of motor can be changed by exchange of phases or usage of suitable ESC That fits 300A regulators and 6-10S Propeller at 6S | 55-57mm | pitch 1.4 | 2 blade Propeller at 6S | 54-56mm | pitch 1.4 | 3 blade Propeller at 8S | 54-63mm | pith 1.4 | 2 blade Propeller at 8S | 53-62mm | pith 1.4 | 3 blade Propeller at 10S | 54-65mm | pitch 1.4 | 2 bladePropeller at 10S | 53-64mm | pitch 1.4 | 3 bladeFor further questions please contact us
€385.00*
instead of
€406.40*
single purchase price (5.27% saved)
%
Brushless motor | 5692-730KV | Bundle Box | Inrunner motor
Bundle Box including suitable parts1x Brushless motor 5692-730KV | 22151x Motor mount 50er motor | 24131x Water cooling jacket 50er motor | 2217.21x Collet clutch 8 - 6,35mm (0,31 - 1/4") | 1023-8The advantages at a glance6 pole rotorDouble ball bearingGood torque | heat build-up ratioHigh balanced magnet armatureSmooth running even at high speedsDirection of rotation of the motor can be changed by changing the phasesThat fits Model boats from approx. 1,15m length 240 - 300A ESC8S | 2 blade propellers | Aluminum | slope 1.4 | Diameter 55-60mm 8S | 3 Blade Propeller | Aluminum | slope 1.4 | Diameter 54-59mm 10S | 2 blade propellers | Aluminum | slope 1.4 | Diameter 58-62mm 10S | 3 Blade Propeller | Aluminum | slope 1.4 | Diameter 57-61mm12S | 3 Blade Propeller | Aluminum | slope 1.4 | Diameter 57-64mm12S | 3 Blade Propeller | Aluminum | slope 1.4 | Diameter 56-63mmFor further questions please contact us
€240.00*
instead of
€261.00*
single purchase price (8.05% saved)
%
Brushless motor | 5692-1000KV | Bundle Box | Inrunner motor
Bundle box including suitable motor parts1x Brushless motor 5692-1000KV | 22161x Motor mount 50er motor | 24131x Water cooling jacket 50er motor | 2217.21x Collet clutch 8 - 6,35mm (0,31 - 1/4") | 1023-8The advantages at a glance6 pole rotorDouble ball bearingGood torque | heat build-up ratioHigh balanced magnet armatureSmooth running even at high speedsDirection of rotation of the motor can be changed by changing the phasesThat fits Model boats from approx. 1,15m length 240 - 300A ESC8S | 2 blade propellers | Aluminum | slope 1.4 | Diameter 55-60mm 8S | 3 Blade Propeller | Aluminum | slope 1.4 | Diameter 54-59mm 10S | 2 blade propellers | Aluminum | slope 1.4 | Diameter 58-62mm 10S | 3 Blade Propeller | Aluminum | slope 1.4 | Diameter 57-61mm12S | 3 Blade Propeller | Aluminum | slope 1.4 | Diameter 57-64mm12S | 3 Blade Propeller | Aluminum | slope 1.4 | Diameter 56-63mmFor further questions please contact us
€240.00*
instead of
€261.00*
single purchase price (8.05% saved)