Rudder Strut Set | 4,75mm (3/16")
€93.00*
Content:
1 Piece
In stock, delivery time: 1-5 labor days**
Product number:
1070
Shipping weight/volume:
0.2 kg
Available stock:
45
Product information "Rudder Strut Set | 4,75mm (3/16")"
Rudder Strut Set for your boat between 70–100cm (27,6"–39,4")
Perfect for your boat because of:
- Both-sided rudder sterring device
- Made from high quality aluminium 7075
- Drive shaft made of V2A (stainless steel)
- Suitable for usage in salt water as well
- Plain bearings installed in the drives ensure high efficiency and low maintenance (compared to ball bearings)
- Thrust bearing washers are made of the highes quality PEEK material. This material is also resistant to most chemicals
- The rudder blade automatically folds upwards in the event of collision with flotsam. Damage to the hull caused by the rudder itself is thereby prevented.
Thats included:
- Rudder - Strut system
- Adapter for Brass PTFE hose 7mm
- PEEK thrust bearing
Good to know
- We recommend a distance of 1,5mm between drive dog and drive body
- For assembly we recommend to use of 4 x M3 screws. A small trick helps to mark the holes at the transom. Place a white piece of paper on the rudder stand and strip several times with a pencil over it. By doing so, you "copy" the exact contours of the holder. Now simply cut the template, stick to the transom with adhesive tape and drill the required holes.
| Total length: | 130mm (5,12") |
|---|---|
| Length outrigger: | 95mm (3,74") |
| Height outrigger: | 55mm (2,17") |
| Flange: | 33x21mm (1,3 x 0,83") |
| Total length rudder blade: | 110mm (4,33") |
| Prop shaft: | For 4,75mm (3/16") flex shaft | For 4,75mm (3/16") propeller |
| Color: | Anodized black |
| Material: | Aluminium 7075 |
Rudder Strut Set | 4,75mm (3/16")
Product safety information:
Manufacturer:
MHZ GmbH
Hauptstrasse 61a
96182 Reckendorf | Germany
Email: shop@mhz-powerboats.com
Hauptstrasse 61a
96182 Reckendorf | Germany
Email: shop@mhz-powerboats.com
That fits
Flex shaft | 4,75mm (3/16") | 100cm (39,37") | Left
Highest quality for highest demandsWith our flex shaft your project will have no limitThe advantages at a glance:High quality for high power setups4,75mm (3/16") diameterProduct photo shows delivered directionThats how its doneFor best connection we recommend to sand back the flex shaft end, degrease and glue into the prop shaft with Loctite.
€15.50*
Flex shaft | 4,75mm (3/16") | 100cm (39,37") | Right
Highest quality for highest demandsWith our flex shaft your project will have no limitThe advantages at a glance:High quality for high power setups4,75mm (3/16") diameterProduct photo shows delivered directionThats how its doneFor best connection we recommend to sand back the flex shaft end, degrease and glue into the prop shaft with Loctite.
€15.50*
Brass PTFE Hose | Steven pipe | 7mm (0,27") | 30cm (11,81") length
Protection for your flex shaftOur brass ptfe hose ensures free spinning for your flex shaft inside your boat and avoids vibration.The advantages at a glanceEasily bandable bras pipe for individual adjustment to your boatSuitable for 4,75mm (3/16") flex shaft Greasy PTFE material avoids friction between flex shaft and brass pipeThats how its doneWe recommend to grease your flex shaft frequently.
€8.00*
Hull passage | Transmission brass pipe | 7mm (0,28")
A clean thingFor easy and sealed assembly of the brass pipe / stern tube. The advantages at a glance Clean sealing of the hull passage Horizontal adjustment of the drive easily possible Delivery includes 2 NBR O-rings for additional sealingHow to do it The installation is generally as deep as possible in the V of the hull Drill a hole with a diameter of 18.5mm (0,73")Grease the supplied O-rings and insert them into the groove Apply polymeric adhesive to the knurled portion of the passage Push transmission into the hole and leave to dry for 24 hours
€8.50*
Hull passage | Transmission brass pipe | 7mm (0,28")
A clean thingFor easy and sealed assembly of the brass pipe / stern tube. The advantages at a glance Clean sealing of the hull passage Horizontal adjustment of the drive easily possible Delivery includes 2 NBR O-rings for additional sealingHow to do it The installation is generally as deep as possible in the V of the hull Drill a hole with a diameter of 18.5mm (0,73")Grease the supplied O-rings and insert them into the groove Apply polymeric adhesive to the knurled portion of the passage Push transmission into the hole and leave to dry for 24 hours
€12.00*
Rudder steering | Linkage set | Several versions
Thread:
M3
Remain on trackWith our rudder linkage, direct and precise control of the rudder is no problem. The connection with the rudder is done by ball heads which can be easily connected to the steering device of your rudder.That's included2 x brass guide tube 2 x stainless steel cable with threaded bush 2 x ball heads 2 x linkage connection How is it done?You need a 3.2mm hole. The brass tube is inserted into this and sealed from the inside with polymer adhesive. We recommend to grease the flex shaft with flex shaft grease before mounting. Due to the fitting accuracy of brass tube and flexible shaft as well as the lubrication with flex shaft grease, the entry of water is reliably prevented. Additionally you may also use rubber seals.Good to knowFor a secure fit, we recommend attaching the brass guide tube to the side of the servo holder. For this purpose, polymer adhesive is suitable.
from €18.00*
Rudder steering | Linkage set | Several versions
Thread:
M2,5
Remain on trackWith our rudder linkage, direct and precise control of the rudder is no problem. The connection with the rudder is done by ball heads which can be easily connected to the steering device of your rudder.That's included2 x brass guide tube 2 x stainless steel cable with threaded bush 2 x ball heads 2 x linkage connection How is it done?You need a 3.2mm hole. The brass tube is inserted into this and sealed from the inside with polymer adhesive. We recommend to grease the flex shaft with flex shaft grease before mounting. Due to the fitting accuracy of brass tube and flexible shaft as well as the lubrication with flex shaft grease, the entry of water is reliably prevented. Additionally you may also use rubber seals.Good to knowFor a secure fit, we recommend attaching the brass guide tube to the side of the servo holder. For this purpose, polymer adhesive is suitable.
from €18.00*