Hull passage | Transmission brass pipe | 7mm (0,28")
€12.00*
Content:
1 Piece
In stock, delivery time: 1-5 labor days**
Product number:
1070-1.2
Shipping weight/volume:
0.1 kg
Available stock:
58
Product information "Hull passage | Transmission brass pipe | 7mm (0,28")"
A clean thing
For easy and sealed assembly of the brass pipe / stern tube.
The advantages at a glance
- Clean sealing of the hull passage
- Horizontal adjustment of the drive easily possible
- Delivery includes 2 NBR O-rings for additional sealing
How to do it
- The installation is generally as deep as possible in the V of the hull
- Drill a hole with a diameter of 18.5mm (0,73")
- Grease the supplied O-rings and insert them into the groove
- Apply polymeric adhesive to the knurled portion of the passage
- Push transmission into the hole and leave to dry for 24 hours
Technical datas
| Length: | 50mm (1,97") |
|---|---|
| Outer diameter: | 18,6mm (0,73") |
| Inner diameter: | 7mm (0,28") |
| Material: | Aluminium 7075 |
| Color: | Black |
Hull passage | Transmission brass pipe | 7mm (0,28")
Product safety information:
Manufacturer:
MHZ GmbH
Hauptstrasse 61a
96182 Reckendorf | Germany
Email: shop@mhz-powerboats.com
Hauptstrasse 61a
96182 Reckendorf | Germany
Email: shop@mhz-powerboats.com
That fits
Rudder Strut Set | 4,75mm (3/16")
Rudder Strut Set for your boat between 70–100cm (27,6"–39,4")Perfect for your boat because of:Both-sided rudder sterring deviceMade from high quality aluminium 7075Drive shaft made of V2A (stainless steel) Suitable for usage in salt water as wellPlain bearings installed in the drives ensure high efficiency and low maintenance (compared to ball bearings)Thrust bearing washers are made of the highes quality PEEK material. This material is also resistant to most chemicalsThe rudder blade automatically folds upwards in the event of collision with flotsam. Damage to the hull caused by the rudder itself is thereby prevented.Thats included: Rudder - Strut system Adapter for Brass PTFE hose 7mm PEEK thrust bearing Good to knowWe recommend a distance of 1,5mm between drive dog and drive bodyFor assembly we recommend to use of 4 x M3 screws.
A small trick helps to mark the holes at the transom. Place a white piece of paper on the rudder stand and strip several times with a pencil over it. By doing so, you "copy" the exact contours of the holder. Now simply cut the template, stick to the transom with adhesive tape and drill the required holes.For further questions please contact us
€93.00*
Flex shaft | 4,75mm (3/16") | 100cm (39,37") | Left
Highest quality for highest demandsWith our flex shaft your project will have no limitThe advantages at a glance:High quality for high power setups4,75mm (3/16") diameterProduct photo shows delivered directionThats how its doneFor best connection we recommend to sand back the flex shaft end, degrease and glue into the prop shaft with Loctite.
€16.50*
Flex shaft | 4,75mm (3/16") | 100cm (39,37") | Right
Highest quality for highest demandsWith our flex shaft your project will have no limitThe advantages at a glance:High quality for high power setups4,75mm (3/16") diameterProduct photo shows delivered directionThats how its doneFor best connection we recommend to sand back the flex shaft end, degrease and glue into the prop shaft with Loctite.
€16.50*
Brass PTFE Hose | Steven pipe | 7mm (0,27") | 30cm (11,81") length
Protection for your flex shaftOur brass ptfe hose ensures free spinning for your flex shaft inside your boat and avoids vibration.The advantages at a glanceEasily bandable bras pipe for individual adjustment to your boatSuitable for 4,75mm (3/16") flex shaft Greasy PTFE material avoids friction between flex shaft and brass pipeThats how its doneWe recommend to grease your flex shaft frequently.
€8.00*