Easy and cost - effective solutionSuitable for model boats between 250mm - 440mm (9,84" - 17,3"). The rudder blade does have an integrated water inlet. Thats includedRudder with rudder blade with integrated water inlet2 Assembly screws M3 with stop nutsSteering rod with rod connectionFor further questions please contact us
Easy and cost - effective solutionSuitable for model boats between 340mm - 600mm (13,39" - 23,6"). The rudder blade does have an integrated water inlet. Thats includedRudder with rudder blade with integrated water inlet2 Assembly screws M3 with stop nutsSteering rod with rod connectionRubber cuffFor further questions please contact us
Rudder with double steering for your boat from 70 - 100cm (2,76 - 3,94")The advantages at a glance: Two-sided rudder linkage device Look a like screws on top for scale look Assembly is done by 2 srews and flange directly - no special transom of hull requiredBlack anodizing for added protection against corrosion The rudder blade is designed in such a way that it automatically folds up in the event of an impact with flotsam in order to prevent damage Good to knowA little trick helps when marking the holes at the rear. To do this, place a piece of white paper on the rudder stand and stroke over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.
Rudder Strut Set for your boat between 70–100cm (27,6"–39,4")Perfect for your boat because of:Both-sided rudder sterring deviceMade from high quality aluminium 7075Drive shaft made of V2A (stainless steel) Suitable for usage in salt water as wellPlain bearings installed in the drives ensure high efficiency and low maintenance (compared to ball bearings)Thrust bearing washers are made of the highes quality PEEK material. This material is also resistant to most chemicalsThe rudder blade automatically folds upwards in the event of collision with flotsam. Damage to the hull caused by the rudder itself is thereby prevented.Thats included: Rudder - Strut system Adapter for Brass PTFE hose 7mm PEEK thrust bearing Good to knowWe recommend a distance of 1,5mm between drive dog and drive bodyFor assembly we recommend to use of 4 x M3 screws.
A small trick helps to mark the holes at the transom. Place a white piece of paper on the rudder stand and strip several times with a pencil over it. By doing so, you "copy" the exact contours of the holder. Now simply cut the template, stick to the transom with adhesive tape and drill the required holes.For further questions please contact us
Rudder Strut Set for your boat between 70–100cm (27,6"–39,4")Bundle Box for fast and easy assembly. Thats included: 1x Rudder - Strut system | 10701x Adapter for Brass PTFE hose 7mm 1x PEEK thrust bearing 1x Steering | 18331x Brass PTFE hose 7mm x 30cm | 10021x Flex shaft 4,75mm (3/16") | 10901x Hull transmission 7mm | 1070-1
Perfect for your boat because of:Both-sided rudder sterring deviceMade from high quality aluminium 7075Drive shaft made of V2A (stainless steel) Suitable for usage in salt water as wellPlain bearings installed in the drives ensure high efficiency and low maintenance (compared to ball bearings)Thrust bearing washers are made of the highes quality PEEK material. This material is also resistant to most chemicalsThe rudder blade automatically folds upwards in the event of collision with flotsam. Damage to the hull caused by the rudder itself is thereby prevented.Good to know
We recommend a distance of 1,5mm between drive dog and drive body
For assembly we recommend to use of 4 x M3 screws.
A small trick helps to mark the holes at the transom. Place a white piece of paper on the rudder stand and strip several times with a pencil over it. By doing so, you "copy" the exact contours of the holder. Now simply cut the template, stick to the transom with adhesive tape and drill the required holes.For further questions please contact us
€130.00*
instead of
€143.00*single purchase price (9.09% saved)
Universal rudder with double steering and 2 way option for usageSuitable for your boat between 100-140cm (39,37" - 55,12").The advantages at a glance: This universal rudder can be used in 2 ways. Either with attachment to rump of boat directly or with universal flange which also enlarges outrigger of rudder thenScale look Both sided rudder linkage device The rudder blade is designed in such a way that it automatically folds up in the event of an impact with flotsam in order to prevent damage Good to knowA little trick helps when marking the holes at the rear. To do this, place a piece of white paper on the rudder stand and stroke over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.
Rudder with double steering and many featuresSuitable for your Mystic 840mm.The advantages at a glance: Two-sided rudder linkage device Look a like screws on top for scale look Assembly is done by 2 srews and flange directly - no special transom of hull requiredBlack anodizing for added protection against corrosion The rudder blade is designed in such a way that it automatically folds up in the event of an impact with flotsam in order to prevent damage Good to knowA little trick helps when marking the holes at the rear. To do this, place a piece of white paper on the rudder stand and stroke over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.
Rudder with double steering and many features
Suitable for your Mystic 1140mm.The advantages at a glance: Two-sided rudder linkage device Black anodizing for added protection against corrosion The rudder blade is designed in such a way that it automatically folds up in the event of an impact with flotsam in order to prevent damage Good to knowA little trick helps when marking the holes at the rear. To do this, place a piece of white paper on the rudder stand and stroke over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.
Rudder with double steering Suitable for your boat between 100-160cm (39,37" - 62,99").The advantages at a glance: Both sided rudder linkage device Universal usableThe rudder blade is designed in such a way that it automatically folds up in the event of an impact with flotsam in order to prevent damage Good to knowA little trick helps when marking the holes at the rear. To do this, place a piece of white paper on the rudder stand and stroke over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.
Bundle box for fast and easy assembly - Rudder with double steering Suitable for your boat between 100-160cm (39,37" - 62,99").Thats included1x Rudder | 10841x Rudder steering | 18331x Hydraulic dummie | 2206The advantages at a glance: Both sided rudder linkage device Universal usableThe rudder blade is designed in such a way that it automatically folds up in the event of an impact with flotsam in order to prevent damage Good to knowA little trick helps when marking the holes at the rear. To do this, place a piece of white paper on the rudder stand and stroke over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.
from €90.00*
instead of
€106.00*single purchase price (15.09% saved)
Rudder with double steering and many featuresSuitable for your Mystic 1380mm.The advantages at a glance: Two-sided rudder linkage device Black anodizing for added protection against corrosion The rudder blade is designed in such a way that it automatically folds up in the event of an impact with flotsam in order to prevent damage Good to knowA little trick helps when marking the holes at the rear. To do this, place a piece of white paper on the rudder stand and stroke over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.
Rudder with double steering and many featuresSuitable for your Mystic 1850 - 1890mm (72,8 - 74,4").The advantages at a glance: Two-sided rudder linkage device Black anodizing for added protection against corrosion The rudder blade is designed in such a way that it automatically folds up in the event of an impact with flotsam in order to prevent damage Good to knowA little trick helps when marking the holes at the rear. To do this, place a piece of white paper on the rudder stand and stroke over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.
Rudder with double steering for your boat from 120cm (47,24")The advantages at a glance: Two-sided rudder linkage device Waterproof, clean finish with rubber sleeve guide Black anodizing for added protection against corrosion Extra reinforced mounting flange up to the rudder boom - therefore absolutely torsion-proof The rudder blade is designed in such a way that it automatically folds up in the event of an impact with flotsam in order to prevent damage Rudder blade available in several lengthsGood to knowWe recommend using 4 x M4 screws for assembly. A little trick helps when marking the holes at the rear. To do this, place a piece of white paper on the rudder stand and stroke over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.
Universal complete system for your boat from 120cm (47,24")The advantages at a glance: Two-sided rudder linkage device Height adjustable strut Waterproof, clean finish with rubber sleeve guide Black anodizing for added protection against corrosion Extra reinforced mounting flange up to the rudder boom - therefore absolutely torsion-proof The rudder blade is designed in such a way that it automatically folds up in the event of an impact with flotsam in order to prevent damage Rudder blade available in several lengthsThats included: Rudder - strut system with linkage levers on both sides Thrust washer made of PEEK material Good to knowWe recommend using 4 x M4 screws for assembly. A little trick helps when marking the holes at the rear. To do this, place a piece of white paper on the rudder stand and stroke over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.For further questions please contact us
Universal complete system for your boat from 120cm (47,24")Bundle Box for fast and easy assembly
Thats included:1x Rudder - strut system with linkage levers on both sides | 10681x Thrust washer made of PEEK material 1x Brass PTFE pipe 10mm x 30cm | 10031x Flex shaft 6,35mm (1/4") | 10051x Hull transmission 10mm (0,39") | 1070-1.31x Steering | 1833The advantages at a glance: Two-sided rudder linkage device Height adjustable strut Waterproof, clean finish with rubber sleeve guide Black anodizing for added protection against corrosion Extra reinforced mounting flange up to the rudder boom - therefore absolutely torsion-proof The rudder blade is designed in such a way that it automatically folds up in the event of an impact with flotsam in order to prevent damage Rudder blade available in several lengthsGood to knowWe recommend using 4 x M4 screws for assembly. A little trick helps when marking the holes at the rear. To do this, place a piece of white paper on the rudder stand and stroke over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.
from €149.00*
instead of
€187.60*single purchase price (20.58% saved)
Rudder with boat sided steering for your boat from 150cm (59,1")The advantages at a glance: Two-sided rudder linkage device Waterproof, clean finish with rubber sleeve guide Black anodizing for added protection against corrosion Extra reinforced mounting flange up to the rudder boom - therefore absolutely torsion-proof The rudder blade is designed in such a way that it automatically folds up in the event of an impact with flotsam in order to prevent damage Rudder blade available in several lengthsGood to knowWe recommend using 4 x M4 screws for assembly. A little trick helps when marking the holes at the rear. To do this, place a piece of white paper on the rudder stand and stroke over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.
Universal complete system for your boat from 150cm (59,1")The advantages at a glance: Two-sided rudder linkage device Height adjustable strut Waterproof, clean finish with rubber sleeve guide Black anodizing for added protection against corrosion Extra reinforced mounting flange up to the rudder boom - therefore absolutely torsion-proof The rudder blade is designed in such a way that it automatically folds up in the event of an impact with flotsam in order to prevent damage Rudder blade available in several lengthsThats included: Rudder - strut system with linkage levers on both sides Thrust washer made of PEEK material Good to knowWe recommend using 4 x M4 screws for assembly. A little trick helps when marking the holes at the rear. To do this, place a piece of white paper on the rudder stand and stroke over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.For further questions please contact us
Universal complete system for your boat from 150cm (59,1")Bundle Box for fast and easy assembly.Thats included: 1x Rudder - strut system with linkage levers on both sides | 1069-RS1x Thrust washer made of PEEK material 1x Brass PTFE hose 10mm x 30cm | 10031x Flex shaft 6,35mm (1/4") | 10051x Hull transmission 10mm (0,39") | 1070-1.31x Steering | 1833The advantages at a glance: Two-sided rudder linkage device Height adjustable strut Waterproof, clean finish with rubber sleeve guide Black anodizing for added protection against corrosion Extra reinforced mounting flange up to the rudder boom - therefore absolutely torsion-proof The rudder blade is designed in such a way that it automatically folds up in the event of an impact with flotsam in order to prevent damage Rudder blade available in several lengthsGood to knowWe recommend using 4 x M4 screws for assembly. A little trick helps when marking the holes at the rear. To do this, place a piece of white paper on the rudder stand and stroke over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.For further questions please contact us
from €168.00*
instead of
€202.60*single purchase price (17.08% saved)
Remain on trackWith our rudder linkage, direct and precise control of the rudder is no problem. The connection with the rudder is done by ball heads which can be easily connected to the steering device of your rudder.That's included2 x brass guide tube 2 x stainless steel cable with threaded bush 2 x ball heads 2 x linkage connection How is it done?You need a 3.2mm hole. The brass tube is inserted into this and sealed from the inside with polymer adhesive. We recommend to grease the flex shaft with flex shaft grease before mounting. Due to the fitting accuracy of brass tube and flexible shaft as well as the lubrication with flex shaft grease, the entry of water is reliably prevented. Additionally you may also use rubber seals.Good to knowFor a secure fit, we recommend attaching the brass guide tube to the side of the servo holder. For this purpose, polymer adhesive is suitable.
A visual highlightThis hydraulic dummy simulates the original scale look and is intended as a visual supplement for the actual linkage set.The advantages at a glance Arm length adjustable 75-109mm Made of high-strength aluminum 7075 Threaded rod stainless steel Anodized black as protection against corrosion That's included2x hydraulic dummy (left | right) 2x ball heads 2x screw M2.5 2x stop nut M2.5
Smart supplies for easy rudder steering contains1 x ball socket made of plastic1x ball joint made of aluminiumGood to knowAvailable with M3 as wellas M4 thread. In combintion with a fitting thread rod you can create a fast and easy rudder and servo steering on demand.
Solutions according to your demandsWith this steering connection you are able to create a steering just as required for your boatThe advanatges at a glanceFor individual setupContains 4 pcs. including set screws and nutEasy assembly and disassembly
For your individual steering solutuionsWith this steering arm you are able to create a rudder, servo.... steering of your choice.The advantages at a glance:Available in several version and sizesAvailable with different materialFor individual steering setup