Perfect for riotingThis jet drive is the perfect companion for your model boat with a vertical stern (90°) and a length of at least 1.20 m or your body board. The Jet 52 supplies extrem high maneuverability. The advantages of the Jet 52 at a glance: Nozzle, impeller, stator made of high-strength aluminum 7075 All parts black anodized for extra protection against corrosion  Flow optimized tunnel made of metalVector control (horizontal | vertical) Triple bearing and shaft seal (Simmerring) Direct lubrication via grease nippleSalt water resistantAdjustable angle Left | right  +/- 15° | Up | Down +/- 10° That fits:Boats with a 90° stern and at least 1.20m in length  Body boards | Short impulse drive for stand up paddling boardsInternal and external rotor motors 40-50 series  Gas engines with 26-32ccm  Good to know:The jet must be greased before usageFlush with fresh water after usage in salt waterIf 2 Jets are used, we recommend a minium distance of 80mm between both JetsFor further questions please contact us

Jet driveThis jet drive is the perfect companion for your model boat with a vertical stern (90°) and a length of at least 1.30 m as well as your waveboard, hydrofoil, kitesurf or surfboard.The Jet 58 supplies extrem high maneuverability. The advantages of the Jet 58 at a glance: Nozzle, impeller, stator made of high-strength aluminum 7075 All parts black anodized for extra protection against corrosion  Flow optimized tunnel made of metalSteering Left | RightTriple bearing and shaft seal (Simmerring) Direct lubrication via grease nippleSalt water resistantAdjustable angle Left | right  +/- 15° | Up | Down +/- 10° That fits:Boats with a 90° stern and at least 1.30m in length  Waveboard, Hydrofoil, Kitesurf or SurfboardInternal and external rotor motors 50 series  Gas engines with 26-40ccm  Good to know:The jet must be greased before usageFlush wih fresh water after usage in salt waterFor further questions please contact us

Jet transmissions for electric and combustion engines That fits: Electric motors from 3KW Combustion engines from 1HP Helical gears for high transmission performance and smooth running Two parallel shafts with a distance of 80mm. Good to knowThe gearbox is not filled with oil before shipping to avoid contamination in the package. It is therefore urgently necessary to fill up with 10-15ccm gear oil before use.

Because sometimes things dont go according to planToo close to the shore and your Jet picked up stones or similar and damaged the impeller? No reason to worry. You find a replacement impeller, made of aluminium 7075, for your Jet 52 here.Your Jet is back on the water within 8 stepsLoosen the jet clutch grub screwUnscrew the jet's cooling water nipple Remove the 3 - M4 grub screws on the nozzle of the jet Now remove the rear nozzle Now you need a strong rope or something similar. Put this around the impeller and pull it out of the jet body with the shaft  Now carefully heat the 2 grub screws on the impeller and remove them Detach the impeller from the shaft and replace it - don't forget to secure the grub screws of the new impeller with Loctite as well Now assemble the jet in reverse order and you are ready to go

Because sometimes things dont go according to planToo close to the shore and your Jet picked up stones or similar and damaged the impeller? No reason to worry. You find a replacement stator, made of aluminium 7075, for your Jet 52 here.Your Jet is back on the water within 6 steps Unscrew the screws on the side of the nozzle Take the complete nozzle off the jet Loosen the grub screws on the side that hold the stator in the nozzle Swap the stator Fix this with the grub screws Reassemble the nozzle with stator onto the jet

Spare bearing set for our Jet 52Spare bearing set suitable for our Jet 48 as well as Jet 52. Suitable for repair may required.Thats included: 1 x rubber seal  2x ball bearing 1 x security clip