Sophisticated solutions for highest demandsSuitable drives for your Mystic 840mm and fast and easy assembly as well as perfect driving experience. Due to their special hydrodynamic profile, the scale drives ensure safe handling and additional stability even at high speeds.   Details at a glance  Made of highest quality aluminium 7075   Black anodizing for great looks and protection against corrosion  Special hydrodynamic profile  Stainless steel prop shaft   Salt water reistance  Slight bearings ensure higher efficiency and low maintenance than ball bearings  Washers made of PEEK material for much longer service time than PTFE and other materials.   Good to knowThe drives do have an ajustable angle of +/-4° We recommend a distance of 1,5mm between drive dog and drive bodyTips for easy installation  A little tricks helps marking the holes at the transom. Take a white sheet of paper and place it at the flange of the drive. Use a pencil and gently swipe over the flange. This way the structure is copied to the paper which can be used as template now.  Cut out the paper template and attach it to the transom of the hull by using masking tape. Drill the required holes now.  For fast and easy assembly (insulation) we recommend the usage of polymer glue. For further questions please contact us 

Sophisticated solutions for highest demandsSuitable drives for your Mystic 1140mm and fast and easy assembly as well as perfect driving experience. Due to their special hydrodynamic profile, the scale drives ensure safe handling and additional stability even at high speeds.  Details at a glance Made of highest quality aluminium 7075  Black anodizing for great looks and protection against corrosion Special hydrodynamic profile Stainless steel prop shaft  Salt water reistance Slight bearings ensure higher efficiency and low maintenance than ball bearings Washers made of PEEK material for much longer service time than PTFE and other materials.  Good to knowThe drives do have an ajustable angle of +/-4° We recommend a distance of 1,5mm between drive dog and drive bodyTips for easy installation  A little tricks helps marking the holes at the transom. Take a white sheet of paper and place it at the flange of the drive. Use a pencil and gently swipe over the flange. This way the structure is copied to the paper which can be used as template now.  Cut out the paper template and attach it to the transom of the hull by using masking tape. Drill the required holes now.  For fast and easy assembly (insulation) we recommend the usage of polymer glue. For further questions please contact us 

Sophisticated solutions for highest demandsSuitable drives for your Mystic 1380mm and fast and easy assembly as well as perfect driving experience. Due to their special hydrodynamic profile, the scale drives ensure safe handling and additional stability even at high speeds.  Details at a glance Made of highest quality aluminium 7075  Black anodizing for great looks and protection against corrosion Special hydrodynamic profile Stainless steel prop shaft  Salt water resistance Slight bearings ensure higher efficiency and low maintenance than ball bearings Washers made of PEEK material for much longer service time than PTFE and other materials.  Good to knowThe drives do have an ajustable angle of +/-4° Tips for easy installation  A little tricks helps marking the holes at the transom. Take a white sheet of paper and place it at the flange of the drive. Use a pencil and gently swipe over the flange. This way the structure is copied to the paper which can be used as template now.  Cut out the paper template and attach it to the transom of the hull by using masking tape. Drill the required holes now.  For fast and easy assembly (insulation) we recommend the usage of polymer glue. For further questions please contact us

Sophisticated solutions for highest demandsSuitable drives for your Mystic 1850-1890mm and fast and easy assembly as well as perfect driving experience. Due to their special hydrodynamic profile, the scale drives ensure safe handling and additional stability even at high speeds.  Details at a glance Made of highest quality aluminium 7075  Black anodizing for great looks and protection against corrosion Special hydrodynamic profile Stainless steel prop shaft  Salt water reistance Slight bearings ensure higher efficiency and low maintenance than ball bearings Washers made of PEEK material for much longer service time than PTFE and other materials.   Good to knowThe drives do have an ajustable angle of +/-4° Tips for easy installation  A little tricks helps marking the holes at the transom. Take a white sheet of paper and place it at the flange of the drive. Use a pencil and gently swipe over the flange. This way the structure is copied to the paper which can be used as template now.  Cut out the paper template and attach it to the transom of the hull by using masking tape. Drill the required holes now.  For fast and easy assembly (insulation) we recommend the usage of polymer glue. For further questions please contact us

Sophisticated solutions for highest demands Suitable drives for your Kiton as well as CT-03 and fast and easy assembly as well as perfect driving experience. Due to their special hydrodynamic profile, the scale drives ensure safe handling and additional stability even at high speeds. Details at a glanceMade of highest quality aluminium 7075 Black anodizing for great looks and protection against corrosionSpecial hydrodynamic profileStainless steel prop shaft Salt water reistanceSlight bearings ensure higher efficiency and low maintenance than ball bearingsWashers made of PEEK material for much longer service time than PTFE and other materials. Good to knowThe drives do have an ajustable angle of +/-4°Tips for easy installation A little tricks helps marking the holes at the transom. Take a white sheet of paper and place it at the flange of the drive. Use a pencil and gently swipe over the flange. This way the structure is copied to the paper which can be used as template now.  Cut out the paper template and attach it to the transom of the hull by using masking tape. Drill the required holes now. For fast and easy assembly (insulation) we recommend the usage of polymer glue. For further questions please contact us 

For fine adjustmentThe Power Trimm Midi L from MTC has an optimal fine adjustment by the high-performance sliding bearing. Thus the inclination of the drive can be adjusted individually. That fitsSuitable for boats up to 1100mm.Good to knowWhy slide bearings? Plain bearings convince against ball bearings due to maintenance-free operation and a long service life.We recommend the use of 2 x M3 screws and nuts for assembly. A little trick helps when marking the holes at the stern. To do this, place a sheet of white paper on the rudder pedestal and draw over it several times with a pencil. In this way, you can “trace” the exact contours of the bracket. Now simply cut out the template, stick it to the hull with adhesive tape and drill the required holes.

Popular classic in new best formAs the successor to our sterndrive, we decided to design a new and improved version of the S6 sterndrive.   The improvements at a glance:The body of the Z-drive is no longer made of cast aluminum, but of CNC-milled aluminum 7075The surface is compacted and additionally protected against corrosion and refined by anodizingClosed lubrication with low-viscosity gear grease. Smearing in the boat as in the predecessor is therefore a thing of the pastHelical gears are not pressed, but CNC milled, hardened, ground and therefore much more accurate and robustAll drive shafts are made of stainless steel (V2A). The upper shaft has two bearings, the lower shaft has three bearings and both are sealed by a SimmerringThe output speed is 1:1 Each drive is assembled by hand directly at and by us. A drilling template is also included in the scope of delivery and makes installation easier for you. Good to knowThe drive has a square mount for 6.35mm (1/4") flex shaft. The S6 drive can be used for both left and right rotation Suitable for boats from approx. 1200mm (with double drive 1400mm length) Suitable for 50 electric motors max. 32,000 rpm and 26-32cc power Suitable for use with semi-submerged propeller The drive has a PTFE holder. The brass tube is not inserted into the drive and must be individually supported separately. We recommend a double support at the level of the coupling and the drive.The peak of the torpedo should be for hulls with steps 2-4mm below keel line for hulls without steps 2-4mm above the keel line for assembly Care instructionsThe drive must be commissioned in water only, as otherwise insufficient cooling can lead to damage to the shaft seal. The drive should be greased as required.For further questions please contact us 

Popular classic in new best formAs the successor to our sterndrive, we decided to design a new and improved version of the S6 sterndrive. The improvements at a glance:The body of the Z-drive is no longer made of cast aluminum, but of CNC-milled aluminum 7075The surface is compacted and additionally protected against corrosion and refined by anodizingClosed lubrication with low-viscosity gear grease. Smearing in the boat as in the predecessor is therefore a thing of the pastHelical gears are not pressed, but CNC milled, hardened, ground and therefore much more accurate and robustAll drive shafts are made of stainless steel (V2A). The upper shaft has two bearings, the lower shaft has three bearings and both are sealed by a SimmerringThe output speed is 1:1 Each drive is assembled by hand directly at and by us. A drilling template is also included in the scope of delivery and makes installation easier for you. Good to knowThe drive has a square mount for 6.35mm (1/4") flex shaft. The S6 drive can be used for both left and right rotation Suitable for boats from approx. 1200mm (with double drive 1400mm length) Suitable for 50 electric motors max. 32,000 rpm and 26-32cc power Suitable for use with semi-submerged propeller The drive has a PTFE holder. The brass tube is not inserted into the drive and must be individually supported separately. We recommend a double support at the level of the coupling and the drive.The peak of the torpedo should be for hulls with steps 2-4mm below keel line for hulls without steps 2-4mm above the keel line for assembly  Care instructionsThe drive must be commissioned in water only, as otherwise insufficient cooling can lead to damage to the shaft seal. The drive should be greased as required.For further questions please contact us 

Jet drive for your model boat This small jet drive is the perfect companion for your model boat with a vertical stern (90°) and a length of at least 1.10 mThe Jet 48 supplies extrem high maneuverability.Bundle box for fast and easy assembly including:1x Jet 48 | 17241x Reverse unit | 1723-R1x Elastic coupling 8mm - ....(please choose required coupling size above) | 17211x Adjustable motor- | ESC mount for innrunner motors of 40er series | 2412The advantages of the Jet 48 at a glance: Nozzle, impeller, stator made of high-strength aluminum 7075 All parts black anodized for extra protection against corrosion Flow-optimized tunnel made of carbon filament Vector control (horizontal | vertical) Triple bearing and shaft seal (Simmerring) Direct lubrication via grease nippleSalt water resistantAdjustable angle Left | right  +/- 15° | Up | Down +/- 10°That fits:Boats with a 90° stern and at least 1.10m in length Internal and external rotor motors 30-40 series Gas engines with 20-26ccm Good to know:The jet must be greased before usageFor further questions please contact us

Perfect for riotingThis jet drive is the perfect companion for your model boat with a vertical stern (90°) and a length of at least 1.20 m or your body board. The Jet 52 supplies extrem high maneuverability. The advantages of the Jet 52 at a glance: Nozzle, impeller, stator made of high-strength aluminum 7075 All parts black anodized for extra protection against corrosion  Flow optimized tunnel made of carbon filament or metalVector control (horizontal | vertical) Triple bearing and shaft seal (Simmerring) Direct lubrication via grease nippleSalt water resistantAdjustable angle Left | right  +/- 15° | Up | Down +/- 10° That fits:Boats with a 90° stern and at least 1.20m in length  Body boards | Short impulse drive for stand up paddling boardsInternal and external rotor motors 40-50 series  Gas engines with 26-32ccm  Good to know:The jet must be greased before usageFlush with fresh water after usage in salt waterIf 2 Jets are used, we recommend a minium distance of 80mm between both JetsFor further questions please contact us

Small Jet driveThis small jet drive is the perfect companion for your model boat with a vertical stern (90°) and a length of at least 1.10 m or as a impulse drive for your body board.The Jet 48 supplies extrem high maneuverability.The advantages of the Jet 48 at a glance: Nozzle, impeller, stator made of high-strength aluminum 7075 All parts black anodized for extra protection against corrosion Flow-optimized tunnel made of carbon filament Vector control (horizontal | vertical) Triple bearing and shaft seal (Simmerring) Direct lubrication via grease nippleSalt water resistantAdjustable angle Left | right  +/- 15° | Up | Down +/- 10°That fits:Boats with a 90° stern and at least 1.10m in length Body boardsInternal and external rotor motors 30-40 series Gas engines with 20-26ccm Good to know:The jet must be greased before usageFlush with fresh water after usage in salt waterIf 2 Jets are used, we recommend a minium distance of 80mm between both JetsFor further questions please contact us

Jet drive for your model boat This jet drive is the perfect companion for your model boat with a vertical stern (90°) and a length of at least 1.20 m or small watercraft tool of your choice. The Jet 52 supplies extrem high maneuverability. Bundle box for fast and easy assembly including: 1x Jet 52  - 1723-N-C1x Reverse unit  | 1723-R1x Elastic coupling 8mm - ....(please choose required coupling size above) | 17211x Adjustable motor- | ESC mount for innrunner motors of 50er series | 2413  The advantages of the Jet 52 at a glance: Nozzle, impeller, stator made of high-strength aluminum 7075 All parts black anodized for extra protection against corrosion  Flow optimized tunnel made of carbon filamentVector control (horizontal | vertical)  Triple bearing and shaft seal (Simmerring)  Direct lubrication via grease nipple Salt water resistant Adjustable angle Left | right  +/- 15° | Up | Down +/- 10° That fits:Boats with a 90° stern and at least 1.20m in length  Internal and external rotor motors 40-50 series  Gas engines with 26-32ccm  Good to know:The jet must be greased before usageFor further questions please contat us

Jet driveThis jet drive is the perfect companion for your model boat with a vertical stern (90°) and a length of at least 1.30 m as well as your waveboard, hydrofoil, kitesurf or surfboard.The Jet 58 supplies extrem high maneuverability. The advantages of the Jet 58 at a glance: Nozzle, impeller, stator made of high-strength aluminum 7075 All parts black anodized for extra protection against corrosion  Flow optimized tunnel made of metalSteering Left | RightTriple bearing and shaft seal (Simmerring) Direct lubrication via grease nippleSalt water resistantAdjustable angle Left | right  +/- 15° | Up | Down +/- 10° That fits:Boats with a 90° stern and at least 1.30m in length  Waveboard, Hydrofoil, Kitesurf or SurfboardInternal and external rotor motors 50 series  Gas engines with 26-40ccm  Good to know:The jet must be greased before usageFlush wih fresh water after usage in salt waterFor further questions please contact us

Simple and fast solution  This functional drive set for small boats up to 450mm  (17,71")  length, provides a simple and fast assembly. Thats includedHeight adjustable strut with assembly screws M3Propeller shaft incl. PTFE washer, Drive Dog, Set screw and Torpedo screwFlex shaft 3,2mm (0,13") with square endBrass | PTFe pipePropeller | Plastic | Drive Dog 32mm (1,26")For further questions, please contact us 

Rudder Strut Set for your boat between 70–100cm (27,6"–39,4")Perfect for your boat because of:Both-sided rudder sterring deviceMade from high quality aluminium 7075Drive shaft made of V2A (stainless steel) Suitable for usage in salt water as wellPlain bearings installed in the drives ensure high efficiency and low maintenance (compared to ball bearings)Thrust bearing washers are made of the highes quality PEEK material. This material is also resistant to most chemicalsThe rudder blade automatically folds upwards in the event of collision with flotsam. Damage to the hull caused by the rudder itself is thereby prevented.Thats included: Rudder - Strut system Adapter for Brass PTFE hose 7mm PEEK thrust bearing Good to knowWe recommend a distance of 1,5mm between drive dog and drive bodyFor assembly we recommend to use of 4 x M3 screws. A small trick helps to mark the holes at the transom. Place a white piece of paper on the rudder stand and strip several times with a pencil over it. By doing so, you "copy" the exact contours of the holder. Now simply cut the template, stick to the transom with adhesive tape and drill the required holes.For further questions please contact us

Rudder Strut Set for your boat between 70–100cm (27,6"–39,4")Bundle Box for fast and easy assembly. Thats included:  1x Rudder - Strut system |  10701x Adapter for Brass PTFE hose 7mm  1x PEEK thrust bearing 1x Steering | 1833.11x Brass PTFE hose 7mm x 30cm |  10021x Flex shaft 4,75mm (3/16") | 10901x Hull transmission 7mm | 1070-1 Perfect for your boat because of:Both-sided rudder sterring deviceMade from high quality aluminium 7075Drive shaft made of V2A (stainless steel) Suitable for usage in salt water as wellPlain bearings installed in the drives ensure high efficiency and low maintenance (compared to ball bearings)Thrust bearing washers are made of the highes quality PEEK material. This material is also resistant to most chemicalsThe rudder blade automatically folds upwards in the event of collision with flotsam. Damage to the hull caused by the rudder itself is thereby prevented.Good to know We recommend a distance of 1,5mm between drive dog and drive body For assembly we recommend to use of 4 x M3 screws. A small trick helps to mark the holes at the transom. Place a white piece of paper on the rudder stand and strip several times with a pencil over it. By doing so, you "copy" the exact contours of the holder. Now simply cut the template, stick to the transom with adhesive tape and drill the required holes.For further questions please contact us

Top quality at a good priceBundle box for fast and easy assembly.Thats included:1x Strut 10711x Flex shaft 6,35mm (1/4") - rotation according to order1x Brass PTFE hose 10mm x 30cm 10031x Hull transmission 10mm 1070-1.1The advantages at a glance: Manufactured from high-strength aluminum 7075 Brass tube can be glued directly into the strut Height individually adjustable via the recess in the strut Propeller shaft made of V2A - therefore salt water resistant That fits:  Suitable for boats from 110cm (43,3") Good to knowFor fine adjustment of the strut, we recommend marking the starting position with a pen, for example. This way you can easily find the starting position if the change did not have the desired effect.

Simple design that convincesBundle box for fast and easy assemblyThats included1x Strut 6,35mm (1/4") with outrigger short | 1075-K1x Flex shaft 6,35mm (1/4") - rotation according to order1x Brass PTFE hose 10mm (0,39") | 10031x Hull transmission 10mm (0,39") | 1070-1.1The advantages at a glance: Adjustable inclineMade of high quality aluminum 7075Prop shaft made of V2A - therefore salt water resistant Brass tube can be glued directly into the strut That fits Hydroplane, outrigger, catamaran, monoboat from 110cm (43,3")Good to knowWe recommend using 4 x M4 screws for assembly. A little trick helps when marking the holes at the rear. Place a piece of white paper on the oarstand and rub over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.

Top quality at a good priceSimple but effective strut suitable for boats from 110cm (43,3")The advantages at a glance: Manufactured from high-strength aluminum 7075 Brass tube can be glued directly into the strut Height individually adjustable via the recess in the strut Propeller shaft made of V2A - therefore salt water resistantThat fits: 6.35mm flex shaft and 10mm brass-PTFE tube Good to knowFor fine adjustment of the strut, we recommend marking the starting position with a pen, for example. This way you can easily find the starting position if the change did not have the desired effect.

Simple design that convincesBundle Box for fast and easy assembly.Thats included 1x Strut 6,35mm (1/4") with outrigger long | 1075-L1x Flex shaft 6,35mm (1/4") - rotation according to order 1x Brass PTFE hose 10mm (0,39") | 10031x Hull transmission 10mm (0,39") | 1070-1.1 The advantages at a glance: Adjustable inclineMade of high quality aluminum 7075Prop shaft made of V2A - therefore salt water resistant Brass tube can be glued directly into the strutThat fits Hydroplane, outrigger, catamaran, monoboat from 110cm (43,3")How it´s doneWe recommend using 4 x M4 screws for assembly. A little trick helps when marking the holes at the rear. Place a piece of white paper on the oarstand and rub over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.For further questions please contact us

Simple design that convincesThe advantages at a glance: Adjustable inclineMade of high quality aluminum 7075Prop shaft made of V2A - therefore salt water resistant Brass tube can be glued directly into the strut That fits Hydroplane, outrigger, catamaran, monoboat from 110cm (43,3")Good to knowWe recommend using 4 x M4 screws for assembly. A little trick helps when marking the holes at the rear. Place a piece of white paper on the oarstand and rub over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.For further questions please contact us

Universal complete system for your boat from 120cm (47,24")Bundle Box for fast and easy assembly Thats included:1x Rudder - strut system with linkage levers on both sides |  10681x Thrust washer made of PEEK material 1x Brass PTFE pipe 10mm x 30cm | 10031x Flex shaft 6,35mm (1/4") | 10051x Hull transmission 10mm (0,39") | 1070-1.31x Steering | 1833The advantages at a glance: Two-sided rudder linkage device Height adjustable strut Waterproof, clean finish with rubber sleeve guide Black anodizing for added protection against corrosion Extra reinforced mounting flange up to the rudder boom - therefore absolutely torsion-proof The rudder blade is designed in such a way that it automatically folds up in the event of an impact with flotsam in order to prevent damage Rudder blade available in several lengthsGood to knowWe recommend using 4 x M4 screws for assembly. A little trick helps when marking the holes at the rear. To do this, place a piece of white paper on the rudder stand and stroke over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.

Universal complete system for your boat from 120cm (47,24")The advantages at a glance: Two-sided rudder linkage device Height adjustable strut Waterproof, clean finish with rubber sleeve guide Black anodizing for added protection against corrosion Extra reinforced mounting flange up to the rudder boom - therefore absolutely torsion-proof The rudder blade is designed in such a way that it automatically folds up in the event of an impact with flotsam in order to prevent damage Rudder blade available in several lengthsThats included: Rudder - strut system with linkage levers on both sides Thrust washer made of PEEK material Good to knowWe recommend using 4 x M4 screws for assembly. A little trick helps when marking the holes at the rear. To do this, place a piece of white paper on the rudder stand and stroke over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.For further questions please contact us 

Simple design that convincesThe advantages at a glance: Adjustable inclineMade of high quality aluminum 7075Prop shaft made of V2A - therefore salt water resistant Brass tube can be glued directly into the strut That fits Hydroplane, outrigger, catamaran, monoboat from 110cm (43,3")Good to knowWe recommend using 4 x M4 screws for assembly. A little trick helps when marking the holes at the rear. Place a piece of white paper on the oarstand and rub over it several times with a pencil. In this way you "copy" the exact contours of the holder. Now simply cut out the template, stick it to the fuselage with adhesive tape and drill the required holes.For further questions please contact us